Cut Your Compressed Air Use an Average of 70% - Increase Output 25 Times

The AiRTX Air Saver Nozzles harness the power of compressed air to do BIG blow-off, cooling and parts ejection jobs, without spewing raw compressed air and noise all over your plant. Even small air usage applications can show major cost reductions.

The Air Saver Nozzle gives you cost and performance advantages with air amplification. It amplifies your compressed air flow 25 times, delivering high thrust with just a fraction of the compressed air wasted by open air lines.

A system-wide changeover to Air Saver Nozzles can be like adding compressor capacity. Air Saver Nozzles will:

• cut your energy bill
• increase air flow with reduced noise level
• reduce demand on your compressor
• give you a return on investment in days.

Air Saver Nozzles

Hurricane ¼ in. NPTF Air Saver Force Nozzle Aluminum or Stainless Steel Increased air flow Great for heavy duty applications Long reach with high thrust ¼" compressed air inlet	Hurricane ½ in. NPTF Air Saver Force Nozzle Aluminum or Stainless Steel High thrust at extended distances Great at removing scaley or rusty parts, cleaning molds ½" fitting for large air flow
¼ in. NPTF Air Saver Force Nozzle Aluminum or Stainless Steel Reduced noise level Strong thrust, low compressed air comsumption Move large amounts of scrap ¼" compressed air inlet	Hurricane ½ in. NPTM Aluminum Adjustable Air Saver Nozzle Aluminum Adjustable flow control ½" fitting for large air flow Extra large design for big blowoff performance
1/8 in. NPTM Aluminum Adjustable Air Saver Nozzle Aluminum or Stainless Steel Meets OSHA noise and dead end pressure requirements High volume of air with lowest possible air consumption Adjustable making it easy to adapt to existing application	1/8 in. NPTM Fixed Flow Air Saver Nozzle Brass or Stainless Steel Meets OSHA noise and dead-end pressure requirements 25:1 amplification increases flow without increased consumption Use for ejecting parts from molding machines, chip blow-off, plant air conservation
Hurricane High Thrust Wedge Jet - ¼ NPT Female Inlet Aluminum or Stainless Steel Highest thrust of any nozzle Meets OSHA noise & dead-end pressure requirements No maintenance, no moving parts, no vibration Ejecting parts, blow-off of scrap, cooling extruded parts	High Thrust Wedge Jet - ¼ NPT Female Inlet Aluminum or Stainless Steel Highest thrust of any nozzle Meets OSHA noise & dead-end pressure requirements No maintenance, no moving parts, no vibration Ejecting parts, blow-off of scrap, cooling extruded parts
1/8 in. NPTM Rubbertip Nozzle Rubber Meets OSHA noise and dead end pressure requirements	Barbed Brass Fixed Flow Air Saver Nozzle Brass Meets OSHA noise and dead-end pressure requirements 25:1 amplification increases flow without increased consumption Use for ejecting parts from molding machines, chip blow-off, plant air conservation
1/4 in. NPTM Aluminum Adjustable Flare Nozzle Aluminum Meets OSHA noise and dead end pressure requirements

Compare AiRTX International Nozzles with Your Method

How does the Air Saver Nozzle work?

The Air Saver releases a tiny amount of compressed air at near-sonic velocity through a fine, ring-shaped nozzle. As the high-speed "tube" of air emerges from the nozzle, it creates a strong vacuum along its sides, pulling a much larger volume of surrounding air into the stream. At 12" in front of the nozzle, the airstream is 3-1/2" diameter and capable of producing force levels of 3.4 to 20.1 ozs. (0.096 - 0.570 kg) depending on the setting.

Uses

• Ejecting parts from molding machines and stamping presses
• Blow off chips, trim scrap, swarf
• Part cleaning before painting
• Plant air conservation and noise reduction
• Cooling molded or cast parts
• Cleaning/cooling of metal strip and plastic/paper webs
• Cleaning/cooling of conveyorized or transfer line parts

Stainless steel or aluminum construction

Low-cost aluminum Air Savers are ideal for most industrial applications. Stainless steel units are ideal for:

• food processing applications
• hot corrosive environments
• maximum durability in harsh environments

Always consider our Aluminum Extension rods or our Flexible Sta-Put hoses for those hard to reach or hard to mount locations. The rods and hoses can be added to your order in the shopping cart with each item.

Plastics - Molding

The Stainless Steel 1/8 in. NPTM Adjustable Air Saver Nozzle Model 48009 uses a minimal amount of compressed air to produce high volume and calling for quick parts release. Small size and instant on/off make it ideal for molding machines.

Woodworking - Drilling Chip Removal

The 25:1 air amplification of the Stainless Steel 1/8 in. NPTM Adjustable Air Saver Nozzle Model 48009 provides plenty of cleaning power for a factory air gun, while still meeting OSHA requirements for dead-end pressure and noise limits.

AiRTX Special PRICE!!!!!

The models below are all very special price for you, please inquiry to us. You will get a special price along with our special gift to you.